Metals & Minerals – Rebar A1
$0.00Rebar A1 is referred to a soft or plain rebar, often without tread, and the amount of carbon used in A1 is lower than other types of rebar.
Metals & Minerals – Rebar A2
$0.00The rebar is semi-rigid and is classified in the S340 category. Its appearance is a longitudinal axis and a spiral series relative to the longitudinal axis.
Metals & Minerals – Rebar A3
$0.00The rebar is hard with twisted tread and the rebar is with the spiral tread. It is in the semi-hard category in terms of hardness.
Metals & Minerals – Rebar A4
$0.00The ribbed bar or compound tread baris called the A4 bar. It has a longer durability and strength than A1-A2-A3 rebars.
Metals & Minerals – Ribbed coil
$0.00In a division, the rebar is classified into two branches and coils. The coil rebar, as its name implies, is twisted into coils.
There are two types of coil rebar:
1. Simple coil
2. Ribbed coil
Metals & Minerals Galvanized Color Coated Sheet
$0.00Galvanized sheets are painted for aesthetics, increased resistance and reduced corrosion. If the production of colored galvanized sheets is due to their appearance and decoration, the color coating is of great importance. However, if it is to enhance corrosion resistance, the sheet rust is minimized.
Metals & Minerals Galvanized sheets
$0.00Hot dip galvanizing has been used for over 150 years as a successful commercial method in the world for protecting steel sheets against corrosion. Galvanized products have long service life and high corrosion resistance.
Mono-Annealed or Hard Drawn Copper Wire
$0.00Diameter
- 1.36mm – 3.599mm ± 0.1
Physical Characteristics
- Single Wire
- Annealed or Hard Drawn
- For Annealed Copper Elongation (A250) Table 1 on ASTM B3 Standard
- For Annealed Copper Resistivity (20ºC) >0.15328 Ωg/m2
- For Hard Copper Resistivity (20ºC) >0.15940 Ωg/m2
- For Hard Copper Tensile Strength Table 1 on ASTM B1 Standard
Multi Copper Wire
$0.00Diameter
- 0.155mm – 0.40mm
Physical Characteristics
- Multi Strand Min.2 Strand Max. 16 Strand
- Annealed
- Elongation (A250) Table 1 on ASTM B3 Standard
Oil Gas Pipes
$0.00Oil & Gas Pipes ERW LINE PIPES ACCORDING TO API 5L All chemical, mechanical, hydraulical and nondestructive tests are possible according to API 5L standard. Length 4.27 m upto 13.72 m by customer request. ERW tubes can be produced also under following standard:
a) JIS G3452 SGP, G3444 STK, G3445 STKM, G3454 STPG, G3466 …
Open Sections Pipes
$0.00Introduction to open section profiles
Open sections are profiles that are widely used in the construction industry, salon roofs, warehouses and parking lots. Currently, Pars World Group manufactures a wide variety of common forms and forms of open sections such as door frames, corners and Z profiles to supply the best quality domestic and foreign markets to the domestic and foreign markets.
Oxygen Free Copper Rod
$0.00Technical Specification
- Electrical Conductivity ≥% 101 %IACS
- Oxide Film Thickness ≤ 15-50 Å
- Tensile Strength 175 N/mm²
- Elongation (A250) 38%
- Hydrogen Embrittlement ≥10bends
- 10/10 Twist No defect such as Checks , Flakes , Seams or Overfills
- Drawability 0.05 mm
Oxygen Free Silver Bearing Copper Rod
$0.00Diameter
- 8 mm
- 12.5 mm
- 20 mm
- 23 mm
Technical Specification
- Copper include silver Ag : 0.04% , 0.07% , 0.1% O:0 – 5 ppm Cu : Rem
- Electrical Conductivity ≥% 100 % IACS
- Tensile Strength 175 N/mm²
- Elongation (A200) ≥ 38%
- Hydrogen Embrittlement without breaking
- Tensile Strength
Standard
- EN1977(March 1998)
Pancake Coil Metals & Minerals
$0.00Pancake Coil Copper Tube (PCC) intended for use in the connection, repairs, or alternations of air conditioning or refrigerator units in the field. Pancake tube is in accordance with specifications given in ASTM Standard (B88 , B280) and European Norm standard (EN12735) and other general norms.
Pancake Steel & Products
$0.00Using cast and draw technology are a one of the newest and advanced technology in the world. Copper tube plant has put into from 2014.
Rebbar wire rod
$0.00SAE 1006 and SAE 1008 wires are also classified as low carbon steels. The parameters related to the hot rolling process for this group of wires are different from the previous samples due to their different chemical analysis and microstructure. The chemical analysis as well as the mechanical properties of these wires according to ASTM standard are presented in the table below.
rebbr
$0.00| row | size(mm) | length(m) | weight of each branch(12m) | the number of branch per bounch | analyze |
| 1 | 8 rebar size | 12m | 5 | 400 | A3 |
| 2 | 10 rebar size | 12m | 7.8 | 260 | A3 |
Round bar wire rod
$0.00SAE 1006 and SAE 1008 wires are also classified as low carbon steels. The parameters related to the hot rolling process for this group of wires are different from the previous samples due to their different chemical analysis and microstructure. The chemical analysis as well as the mechanical properties of these wires according to ASTM standard are presented in the table below.
Soudronic Wire Copper Wire
$0.00Technical Specification
- Single wire
- Annealed (or hard : according to the order)
- Tensile Strength 245∼285 MPa
- Elongation (A250) 22∼28%
- Resistivity (20°C) < 0.15328 Ωg/m2 (<0.017241 Ωmm2/m)
Stainless Steel U-Tubes Pipe
$0.00Size Range: OD 19_35 mm, WT 1.6_3.5 mm, L Max 15000 mm
Operative Standard & Grade Standards:
Bending Standard: TEMA &API 660
Type of End‐Finish: Beveled Both Ends or Plain Ends
Coating: Passivation and oiled, Black paint or varnish
Tests and Reports: Tubes are tested according to the standard’s specifications.
Steel Ingot 3SP Steel Billet
$0.00Steel Ingot 3SP Steel Billet
application:
Used in the construction industry, including manufacture of grider, angles and drainpipe.
Steel Ingot 5SP Steel Billet
$0.00Steel Ingot 5SP
application: Used in the construction industry, including manufacture of plain bars and angles.
Steel Ingot 55Cr3 Steel Billet
$0.00Steel Ingot 55Cr3
application: This alloy is highly used in the manufacture of spring steels, which has high tensile strength and resistance to abrasion and vibration under high pressures.
Steel Ingot C50 Steel Billet
$0.00Steel Ingot C50
High quality medium carbon steel is used in forging automobile and engine components, screws, shafts, cutting tools, and hammers. Its high hardness and strength is acquired through performing tempering and quenching operations
Steel Ingot Ck45 Steel Billet
$0.00application:
this alloy is in the category of thermal simple steels medium carbon which is used in the manufacture of pump shafts and medium pressure components. Due to the low percentage of chromium, the compounds of this steel are not resistant to corrosion and rust. This steel is used in the manufacture of agricultural tools, machine shafts, screws, crankshafts and gears. In order to use this alloy in agricultural and tillage components, surface hardening operations which is mostly at reasonable price can be done to increase abrasion and impact resistance
Steel Ingot Ck60 Steel Billet
$0.00Steel Ingot Ck60
application:
This alloy can be used for cases in which necessity for developing abrasion indicators and strength levels are more required than lower carbon rows such as agricultural implements, blades of agricultural tools, hammers, heavy machinery parts, shafts, torsion rods and Wrenches.
Steel Ingot St52 Steel Billet
$0.00Steel Ingot St52
Used in the production of high quality steel pipes and tanks.
Steel Ingot X40CrMoV5-1 Steel Billet
$0.00steel ingot X40CrMoV5-1
application: This high alloy steel is one of the most widely used steels in sections such as hot forging molds like muscles, aluminum die-casting molds, die casting pins, and smithery due to its suitable features such as toughness and high strength.
Straight Metals & Minerals
$0.00Using cast and draw technology are a one of the newest and advanced technology in the world. Copper tube plant has put into from 2014.
Straight Tube Metals & Minerals
$0.00Straight copper tubes are used for air conditioning & refrigeration industries, electrical industries and sanitary purposes. The Straight length Seamless Copper Tubes with high precision, ultra clean surfaces, bright finish, even structure, high efficient heat exchanging, welding easily, corrosion resistant and good for mobility.
Tin Plating Sheet
$0.00| Model : | – |
| Description : | There are numerous applications for tin-plated sheets, including the packaging of foodstuffs, chemicals, drugs, dyestuffs, varnishes, and some applications in the manufacture of parts such as oil, gasoil, air and water filters in vehicles such as lorries, buses, tractors and other heavy-duty vehicles, as well as in the manufacture of light vehicles such as sedans, manufacture of toys, electric batteries, etc. |
| Company name : | Esfahan’s Mobarakeh Steel Company |
| Packaging : | – |
| Minimum order : | 1 |
| Standard : | – |
| Production power : | – |
Tinned Copper Rod Copper Wire
$0.00Diameter
- 0.6 ∼ 2.6 mm ± 1%
Technical Specification
- Single wire
- Annealed (or hard : according to the order)
- Resistivity 20ºC ≤ 0.15940 Ω.g/m²
- Elongation (A250) ≥ Table 1 in ASTM B33
- Continuity of coating : According to section 6.4 in ASTM B33
- Adherence of coating : According to section 6.5 in ASTM B33
- Thickness of tin layer Max. 17 microns
Trolley Wire railway cables
$0.00Diameter
- According to purchase order
Technical Specification
- Single wire
